Simulation of Rock Drilling Process using Smoothed-Particle Hydrodynamics Method
DOI:
https://doi.org/10.22034/AJSE.2012052Keywords:
Rock drilling, Smoothed-particle Hydrodynamics (SPH), Finite element, GraniteAbstract
Drilling operation in other planets and discovery of their available resources, as well as exploiting oil and gas fields of earth planet have focused the attention of the researchers on finding some ways to reduce drilling time and cost. In this regard, the use of optimized and well-designed drilling tools, especially drilling bits, seems to be very essential. Concerning this issue, a proper and reliable estimation of the rock cutting process using diamond bits could be efficient in this process. On the other hand, the simulation and modeling of the cutting process is a complex issue for which various methods have been proposed. In this paper, concerning the special conditions of rock cutting, the drilling process mechanical analysis was done through smoothed-particle hydrodynamics (SPH) and LS-DYNA was used for analysis purpose. Finally, the results of using this method were investigated. Furthermore, the effect of different rake angles was also investigated. Concerning the hydrodynamic behavior of smoothed particles and the appropriate velocity of meshing and analysis, as well as the heterogeneities of materials such as rock in this code, this method could be considered as suitable for drilling analysis.
References
Soleimanimehr H, Mirzaei M, Ghani M, Sattari F, Forouzan-Najafabadi A. The comparison between Micro grooving of aluminum, titanium and magnesium alloys by acidithiobacillus ferrooxidans bacteria. Adv. J. Sci. Eng. 2020;1:16-19.
Soleimanimehr H, Nategh M J, Jamshidi H. Mechanistic model of work-piece diametrical error in conventional and ultrasonic assisted turning. Mater. Manufact. Technol. XIV 2010;445:911-916.
Soleimanimehr H, Nategh MJ, Forouzan-Najafabadi A, Zarnani A. The analysis of the Timoshenko transverse vibrations of workpiece in the ultrasonic vibration-assisted turning process and investigation of the machining error caused by this vibration. Precis. Eng. 2018;54:99-106
Kou SQ, Lindqvist P-A, Tang CA, Xu XH. Numerical simulation of the cutting of inhomogeneous rocks. Int. J. Rock Mech. Min. Sci. 1999;36:711–717.
Cho JW, Jeon S, Yu SH, Chang SH. Optimum spacing of TBM disc cutters: a numerical simulation using the three-dimensional dynamic fracturing method. Tunn. Undergr. Space Technol. 2010;25:230-244.
Cho JW, Jeon S, Jeong HY, Chang SH. Evaluation of cutting efficiency during TBM disc cutter excavation within a Korean granitic rock using linear-cutting-machine testing and photogrammetric measurement. Tunn. Undergr. Space Technol. 2013;35:37-54.
Huang H, Detournay E. Intrinsic length scales in tool-rock interaction. Int. J. Geomech. 2008;8:39-44.
Tan XC, Kou SQ, Lindqvist PA. Application of the DDM and fracture mechanics model on the simulation of rock breakage by mechanical tools. Eng. Geol. 1998;49:277-284.
Menezes PL, Lovell MR, Avdeev IV, Higgs III CF. Studies on the formation of discontinuous rock fragments during cutting operation. Int. J. Rock Mech. Min. Sci. 2014;71:131-142.
Gingold R, Monaghan J. Smoothed particle hydrodynamics- theory and application to non-spherical stars. Mon. Not. R. Astron. Soc. 1977;181:375-389.
Monaghan J. Simulating free surface flows with SPH. J. Comput. Phys. 1994;110:399-406.
Morris J, Fox P, Zhu Y. Modeling low Reynolds number incompressible flows using SPH. J. Comput. Phys. 1997; 136:214-226.
Cleary P, Monaghan J. Conduction modelling using smoothed particle hydrodynamics. J. Comput. Phys. 1999;148:227-264.
Monaghan J, Kocharyan A. SPH simulation of multi-phase flow. Comput. Phys. Commun. 1995;87:225–235.
Cleary P, Prakash M. Discrete-element modelling and smoothed particle hydrodynamics: Potential in the environmental sciences. Philos. Trans. R. Soc. 2004;362:2003-2030.
Deb D, Das S, Pramanik R, Douillet-Grellier T, Pan K, Jones BD, Williams JR. Rock failure process in indirect tension using SPH method. 50th US Rock Mech. Geomech. Sympos. 2016.
Mardalizada A, Manesa A, Giglioa M. The numerical modelling of a middle strength rock material under. Proced. Struct. Integr. 2017;3:395-401
Zhai Y, Li Y, Li Y, Zhang Y, Meng F, Lu M. Impact compression test and numerical simulation analysis of concrete after thermal treatment in complex stress state. Mater. 2019;12:1938.
Zhang GX, Qiang HF, Wang G, Huang QZ, Yang YQ. Numerical simulation of the penetration of granite at wide-range velocities with a new SPH method. AIP Adv. 2019;9:015220.
Cheng Z, Li G, Huang Z, Sheng M, Wu X, Yang J. Analytical modelling of rock cutting force and failure surface in linear cutting test by single PDC cutter. J. Petrol. Sci. Eng. 2019;177:306-316.
Soleimanimehr H, Nategh MJ. An Investigation on the Influence of Cutting?Force’s Components Error in Ultrasonic?Vibration?Error in Ultrasonic Vibration?Assisted Turning. AIP Conf. Proc. 2011;1315:1145-1150.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2020 Advanced Journal of Science and Engineering
This work is licensed under a Creative Commons Attribution 4.0 International License.
This work is licensed under a Creative Commons Attribution 4.0 International License (CC-BY 4.0).
Advanced Journal of Science and Engineering (2020-2023) is licensed under a